Do not take too lightly the forklift at the workplace. If the operation is not good, there will certainly be severe mishaps in mins, and there are numerous crashes involving forklifts.

Case 1: The forklift cargo blocked the vehicle driver's sight, and the person in front might not be discovered, resulting in a moving mishap.
Case 2: In order to maintain the equilibrium of the forklift when lifting hefty products, the staff members utilized their body weight as the weight, which practically triggered casualties.
Case 3: The width of the forklift cargo surpasses the allowable size of the course and holds on the roadside rack, which almost causes an mishap.
Case 4: Forklift is speeding and rolls over throughout a turn.
Case 5: The forklift motorist did not see the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift raises the workers unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is squashed when the forklift surrender.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the vehicle when it surrendered and was crushed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that hinder the security of driving, beep the horn initially and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe before beginning.
3. When the forklift starts with a lots, the chauffeur must first confirm that the load is steady and reputable.
4. The begin should be slow and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the mast ought to be slanted backward. .
2. Do not lift the fork too high when driving. When going into and leaving the job website or while driving, beware that there will certainly be no obstacles in the sky. When the load is taking a trip, the fork should not be increased expensive, which will certainly impact the security of the forklift. .
3. After dumping, the fork should be decreased to the typical driving position before driving. .
4. When transforming, if there are pedestrians or vehicles close by, the driving signal must be provided initially. High-speed doglegs are restricted. High-speed doglegs will create the lorry to shed lateral security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it should obey the traffic rules in the manufacturing facility and have to keep a certain safety distance from the car ahead. .
7. When the forklift is running, the lots needs to remain in the lowest position that does not prevent the driving, and the gantry must be appropriately slanted back. The tons shall not be elevated other than when piling or loading. .
8. The height of the lots need to not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a reduced speed when turning around.
9. It is restricted to activate the ramp, neither to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a reduced speed when going into the production workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for personnel to depend on the fork to hold items and play a stabilizing function. .
12. If problems are discovered, they will be fixed and reported in a timely manner, and they will certainly never ever run with health problems or hide them.

filling and dumping.
1. When fork-loading products, the distance in between both forks must be readjusted as required to make the lots of the two forks well balanced and not manipulated, and one side of the item should be against the shelf. .
2. It is prohibited to work with a solitary fork or make Stand-on Electric Pallet Stacker use of a fork top or pull. In special situations, safety and security indication have to be set up to remind surrounding pedestrians. .
3. In the process of packing and discharging things, the forklift has to be stopped with the brake. .
4. The speed of the lorry need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When using a fork to fork the goods, the fork should be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch various other goods or items. The lots needs to be maintained with minimal back tilt of the gantry to ensure that the lots does not glide backwards. The pole can be tilted ahead somewhat when the load is reduced to permit easy placement of the lots and extraction of the forks. .
6. It is forbidden to fork products at high speed and hit hard items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so as to avoid the collapse of the goods and harm people. .
8. Straining is restricted, and it is restricted to use forks to lift workers to take part in high-altitude operations to stay clear of high-altitude falling crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll items. .
10. It is not allowed to make use of forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Prior to leaving the forklift, you should unload the goods or reduced the fork framework.
2. Pull the hand brake manage to dead or depress the hand brake button.
3. The engine is turned off and the power is removed. (Except for unique circumstances, such as the motorist does not leave the vehicle's line of vision and does not surpass 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be inspected, and gas, lubricating oil and air conditioning water ought to be included.
2. Examine the security efficiency of starting, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. During the procedure of the forklift, examine whether the stress and temperature are regular.
5. After the forklift is running, the external leak must likewise be inspected and the seals should be replaced in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the cars and truck;.
2. When you run into someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m above the ground;.
5. The transforming should not be too sharp to avoid the propensity of " totally free turning";.
6. Adding and down the incline should be sluggish and consistent, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the slope is more than 10%, the automobile must be driven in reverse when worsening;.
8. When the forklift personnel lug the goods and progress, if they come across huge or hefty items and most likely to the vehicle driver's line of sight, they should take the turning around workout
.
The "Eight Prohibitions" need to be followed in the operation.
1. Solitary fork operation is not allowed.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to pick up the goods by handing over the pallet with the fork.
4. It is not enabled to directly shovel chemicals, flammables and other hazardous chemicals with forks.
5. It is not allowed to use inertia force to grab the goods.
6. It is not enabled to utilize braking pressure to exile round or easy-to-roll objects.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Curves, slim roadways, railway crossings;.
2. Areas with a longitudinal slope more than 5%.
3. When there is an barrier on one side of the road, the contrary Stand-on Electric Pallet Stacker side of the area with the same size as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844